grads打开ctl有问题。

yqy1204

可以打开nc的数据，但是需要批处理，然后写ctl ,求助啊

WZZ809525579

ctl贴出来看看啊

独奏古筝到天明

ctl脚本的问题

yqy1204

WZZ809525579 发表于 2017-5-10 11:20
ctl贴出来看看啊

dset E:\gldasnc\GLDAS\GLDAS_NOAH10_M.A196002.020.nc
title NCL: convert-GRIB-to-netCDF
undef 1e+20
dtype netcdf
xdef 360 linear -179.5 1
ydef 150 linear -59.5 1
zdef 1 linear 0 1
tdef 1 linear 00Z01JAN0001 1mn
vars 20
Qs_GDS0_SFC_ave30d=>qs_gds0_sfc_ave  0  y,x  Surface Runoff
Qsb_GDS0_SFC_ave30d=>qsb_gds0_sfc_av  0  y,x  Subsurface Runoff
Canopint_GDS0_SFC_ave30d=>canopint_gds0_s  0  y,x  Plant canopy surface water
LWdown_GDS0_SFC_ave30d=>lwdown_gds0_sfc  0  y,x  Surface incident longwave radiation
SWdown_GDS0_SFC_ave30d=>swdown_gds0_sfc  0  y,x  Surface incident shortwave radiation
Rainf_GDS0_SFC_ave30d=>rainf_gds0_sfc_  0  y,x  Rainfall rate
Snowf_GDS0_SFC_ave30d=>snowf_gds0_sfc_  0  y,x  Snowfall rate
Qg_GDS0_SFC_ave30d=>qg_gds0_sfc_ave  0  y,x  Ground Heat Flux
AvgSurfT_GDS0_SFC_ave30d=>avgsurft_gds0_s  0  y,x  Average Surface Temperature
Qh_GDS0_SFC_ave30d=>qh_gds0_sfc_ave  0  y,x  Sensible Heat Flux
Qle_GDS0_SFC_ave30d=>qle_gds0_sfc_av  0  y,x  Latent Heat Flux
LWnet_GDS0_SFC_ave30d=>lwnet_gds0_sfc_  0  y,x  Net Longwave Radiation
SWnet_GDS0_SFC_ave30d=>swnet_gds0_sfc_  0  y,x  Net Shortwave Radiation
Qsm_GDS0_SFC_ave30d=>qsm_gds0_sfc_av  0  y,x  Snowmelt
SWE_GDS0_SFC_ave30d=>swe_gds0_sfc_av  0  y,x  Snow Water Equivalent
Evap_GDS0_SFC_ave30d=>evap_gds0_sfc_a  0  y,x  Total Evapotranspiration
Qair_GDS0_SFC_ave30d=>qair_gds0_sfc_a  0  y,x  Near surface specific humidity
Wind_GDS0_SFC_ave30d=>wind_gds0_sfc_a  0  y,x  Near surface wind speed
Tair_GDS0_SFC_ave30d=>tair_gds0_sfc_a  0  y,x  Near surface air temperature
PSurf_GDS0_SFC_ave30d=>psurf_gds0_sfc_  0  y,x  Surface pressure
endvars

启元YIN

ctl 文件中dset 后的 nc 文件路径对吗？

yqy1204

启元YIN 发表于 2017-5-10 18:27
ctl 文件中dset 后的 nc 文件路径对吗？

已经改好了，谢谢啊